 |
 |
 |
|
Fashionable, fast, and foolproof! A headband wig of long loose waves trimmed in tapered layers to be shorter in the front, longer in the back.
HairUWear has created an exclusive version of their remarkable True2Life® synthetic hair for the Kim Kimble Hair Collection.
The light, soft, and lustrous texture looks and feels like real hair.
Important:
- Take special care with lace front wigs & hairpieces. The lace is delicate and should not be tugged or pulled.
- Sudden bursts of heat such as opening an oven door, may damage heat-friendly synthetic fiber.
- We do not recommend sleeping, showering, or swimming while wearing.
- For longer styles, comb through nape area often using your fingers or wide-tooth comb.
- Hair color cannot be used on synthetic fiber.
Pre-Wash
- Gently remove tangles using your fingers or a wide-tooth comb. (Do not use a brush). Start at the ends and slowly work toward the base to avoid damage. Do not overstretch or pull on the fiber.
Wash/Condition
- Add 1 tbsp of shampoo to a washbasin of cool water. (Caution: Hot water will damage synthetic fiber)
- Soak wig or hairpiece in wash basin for 3-5 minutes. Do not scrunch or agitate. (Caution: Soaking longer than 5 minutes may damage the wig or hairpiece)
- Rinse under cool running water until the water runs clear. Use a clean, colorfast towel to gently press out excess water. Do not twist or wring.
- Apply a light mist of spray-on leave-in conditioner and comb through using a wide-tooth comb starting at the ends. (Caution: Do not apply conditioner directly to hand-tied areas as this may loosen the knots and cause shedding)
- For wavy/curly styles, be careful not to overstretch or pull on the fiber.
- The damp wig can then be placed on a wig stand to dry. Hairpieces can be clipped on a hanger to dry, however hand-tied hairpieces should instead dry flat on a colorfast towel to prevent any damage to the delicate construction. (Caution: Do not dry wig on a solid form or mannequin head to avoid overstretching the cap)
Styling
- Shake to release the fiber. Style with your fingers to achieve the desired look.
- Tru2Life fiber can be curled, waved, flat-ironed or blown dry to achieve a different texture. Once heat-styled, the wig or hairpiece will keep the new texture even after washing.
- Suggestion: Use a light mist of heat-protectant silicone spray prior to heat-styling
- Tru2Life fiber can withstand a low-medium heat setting up to 350 degrees F / 180 degrees C (Caution: Fiber will be damaged if the heat setting is too high. Do not heat-style while wearing as heat-friendly synthetic fiber will get very hot.)
- To Straighten: take a 1-inch section and run a flat iron from the base to the ends. Allow to cool.
- To curl: wrap a 1-inch section around a curling iron and hold for 10 seconds. Carefully slide the iron out and hold the curl shape with a hairpin or clip until completely cool to set the curl.
- For wavy/curly styles, refresh the texture as needed by spritzing with 50/50 mix of water and spray-on leave-in conditioner while finger-styling.
Maintenance
- After each wearing, gently comb through the wig or hairpiece using your fingers or wide-tooth comb
- To avoid unwanted kinks or crimps in the base material, store wig on a wig stand or clip hairpiece to a hanger
- To maintain wavy/curly textures, style only when the hair is completely dry using only your fingers. Do not comb or brush dry hair as this can loosen the texture.
- After extended wear, matting and frizzing can occur. To detangle and recondition, wash as recommended, spray with leave-in conditioner, then comb through with a wide-tooth comb starting at the ends.
|
|
|
 |
|
 |
|